5
$\begingroup$

I'm trying to wrap my head around what the PHAK (Pilot's Handbook of Aeronautical Knowledge from the FAA) states for constant speed propellers.

First, why is it that if airspeed increases, for a fixed RPM, your blade pitch will increase, and conversely decrease if airspeed drops? Is it because it wants to maintain that low AOA (2-4 degrees according to the PHAK) with the relative airflow? If its AOA were to increase, such as not changing blade angle as airspeed drops, would drag increase causing the RPM to fall? And if airspeed is too high and AOA is too low, there's not enough drag to slow down the blades?

On takeoff, you want max thrust/power. By setting the blades to low pitch, you get max RPM because the blades take less of a bite out of the air. This also keeps blade AOA low which in turn reduces drag and allows RPM to build? Also, is max thrust in this case the result of the blades generating a lot of lift because of their high velocities from the higher RPM (versus thrust from moving larger chunks of air)?

Why is low RPM preferred in climbs/cruise? If you increase the blade pitch in these flight regimes, you get a smaller AOA with respect to wind which from my understanding so far reduces drag? But then doesn't the blade taking larger bites of air require more power anyways to maintain that RPM? Is it more efficient to give power to blades to move larger loads of air than it is to run at lower blade angles and higher RPM?

And lastly, with regards to blade AOA and relative wind, would a blade generate more lift if it had a higher AOA, but at the expense of additional drag on the blade which in turn requires more engine power? Is this drag induced drag because it's an airfoil?

Improve this question
$\endgroup$
6
  • $\begingroup$ Welcome to aviation.SE! We have a few questions that might help, especially this one and this one. And the tour may be useful if you're new to the site. $\endgroup$
    – Pondlife
    Jun 4, 2019 at 1:59
  • $\begingroup$ Thanks! The first one helped clarify it a bit. But do you know why, from a physics standpoint, we're able to impart less energy into the air and still get the same forward acceleration? It seems like theoretically, to have X amount of force work against drag, you need X amount of energy. How can you justify from an energy/math standpoint a higher angle blade uses less energy? $\endgroup$
    – Flak
    Jun 4, 2019 at 3:02
  • $\begingroup$ Can you maintain highway speed by shifting up gears and easing off on the gas? Twisting the prop more at cruise altitude while slowing down the RPM has the same effect. If you want to accelerate to pass someone, you step on the gas and sometimes downshift. Same with cruising faster or climbing - back off the prop twist and increase the RPMs. $\endgroup$
    – CrossRoads
    Jun 4, 2019 at 3:14
  • $\begingroup$ Ok so what you're saying is you can't achieve high thrust with large blade angles but level flight is not a problem? When you need that extra kick in thrust you need more RPM which leads to higher energy use? $\endgroup$
    – Flak
    Jun 4, 2019 at 3:17
  • $\begingroup$ Yes. You can pull back on the stick (yoke) to start the climb; the prop governor will work to keep the engine RPMs the same, while the higher twist will keep you bogged down. To keep on climbing, you add more thrust and dial back the propeller pitch to allow more horsepower, effectively downshifting and stepping on the gas to stick with the car analogy. $\endgroup$
    – CrossRoads
    Jun 4, 2019 at 12:00

4 Answers 4

Reset to default
5
$\begingroup$

A propeller has an optimum AoA, where the thrust/drag ratio is highest. A variable prop can maintain this optimum AoA at a wide range of speeds, thereby reducing fuel consumption. That's all it does.

Fixed wing propellers have a dilemma that at take-off they require maximum thrust, and in high-speed flight the engine will need to be throttled back to prevent overspeeding. Maximum engine power cannot be utilised at every airspeed.

why is it that if airspeed increases, for a fixed rpm, your blade pitch will increase?

To maintain optimum blade AoA. Increased airspeed causes reduction of blade AoA at constant pitch.

On takeoff, you want max thrust/power.

You want maximum thrust. This is generated by making the propeller spin as fast as possible (not exceeding tip Mach), with a maximum blade pitch where the blade does not stall. Reducing blade pitch to increase RPM results in no increase in thrust: Power = Thrust * RPM.

If you increase the blade pitch in these flight regimes, you get a smaller AOA with respect to wind

No a larger AoA. More thrust and more torque on the propeller axis.

Is it more efficient to give power to blades to move larger loads of air

The engine runs most economically at the RPW where maximum torque is generated, the constant speed propeller speed control wants to maintain that RPM.

would a blade generate more lift if it had a higher AOA, but at the expense of additional drag on the blade which in turn requires more engine power? Is this drag induced drag because it's an airfoil?

Yes and yes :)

Improve this answer
$\endgroup$
10
  • $\begingroup$ Ok, and so as you increase airspeed, you want to increase pitch to maintain optimal AoA? Why does reducing pitch to increase AoA not increase thrust? In climb/cruise, do you need overall less thrust hence why you don't run at high RPM? What do you mean by an RPM where max torque is generated? Is torque not proportional to engine power? $\endgroup$
    – Flak
    Jun 4, 2019 at 16:22
  • $\begingroup$ @Flak, this is more engine properties than propeller properties. RPM limit power, so you need higher RPM for higher power, but it causes more engine wear, so you want lower RPM when you don't need as much power. Piston engines start losing torque beyond some RPM as the charge takes longer part of the stroke to burn through, leaving smaller part for the expansion that does the actual work, so there is RPM where the torque is highest and there the engine is most efficient. Turbines would have similar effect as the turbine blades have fixed pitch, but are usually more limited by wear. $\endgroup$
    – Jan Hudec
    Jun 4, 2019 at 21:13
  • $\begingroup$ @Flak, for propeller efficiency, if you keep high RPM for low power, the blades fly at too low pitch and generate relatively too much parasite drag for the lift, so you want to reduce RPM when you reduce power. But if you try to put too much power at slow RPM, the blade pitch will raise too high and the blades will run at too high pitch, generating too much induced drag or even stalling. So for the propeller, the optimal RPM is also proportional to power. $\endgroup$
    – Jan Hudec
    Jun 4, 2019 at 21:18
  • $\begingroup$ Ok so at cruise, you set RPM based on what you want your power setting to be to both maintain speed and be efficient by balancing induced to parasite drag. This is done by the correct AoA on the blades, which have a preferred most efficient AoA right? Also is torque and power not synonymous? Just because you have more power it doesn't necessarily mean more torque? And blades spinning slowly bc of high AoA and low RPM on takeoff can't produce enough thrust bc despite their high AoA they don't have much velocity right? $\endgroup$
    – Flak
    Jun 4, 2019 at 22:07
  • $\begingroup$ Also. For fixed pitch propellers. Is your max speed limited because your blade AoA will become ineffective at too high forward speed as relative wind changes direction? So it can provide high enough thrust to overcome drag? $\endgroup$
    – Flak
    Jun 5, 2019 at 0:01
3
$\begingroup$

An important thing to keep in mind is that the propeller control system has no idea what the blade angle is (except in BETA mode systems which is another topic completely). It's a flyweight governor that just moves the blades coarser, finer, or holds them static based purely on engine speed, and the speed setting from the prop lever is just increasing or decreasing pre-load on a spring that tends to hold the flyweights in.

The governor just knows: Speed too fast, flyweights move out, routes pressure to move the blades more coarse; speed too slow, flyweights move in, routes pressure to move the blades more fine. How coarse or how fine, the governor does not know or care.

A specific blade angle and AOA is a function of the torque the engine is producing and the speed setting. There will be some optimum AOA at any one time, but since we can't control that specifically, we are only concerned with RPM and let the blade angle take care of itself.

Since total HP is a function of manifold pressure and RPM, I can use a range of different engine speeds and throttle openings to make the same HP. There will be a speed/MP setting that roughly results in blade angles that are optimal when making say 85% power and this would be the recommended power setting for 85% power climb (typically something along the lines of 25" and 2500 RPM say). But I can use a lower RPM and higher MP to make the same horsepower if I wanted, such as 2400 RPM and 26", still making 85% power (I'm just pulling numbers out of my head for illustrative purposes here).

There is an old saw that says "oversquare" settings (low RPM/high MP) like that are bad, but it's not really true unless it's taken to the extreme. There is a benefit to using lower RPM, such as 2100 RPM and 25" MP vs 2300 and 23" to make the same HP, because the engine most benefits from slowing down all the reciprocating parts. Less friction and therefore less heat, and very importantly, piston ring speed, and distance traveled, is less for a given power setting (piston rings wear out based on distance traveled; slow them down and they don't go as far per unit of time). Cylinder internal pressures are higher running oversquare, but unless temperatures are high or there is detonation (a potential only at the extremes, like WOT at min RPM) it's not important (supercharged engines spend their entire lives crazy oversquared).

Operationally, it's the power and RPM that's the main concern, not optimizing blade angle.

Improve this answer
$\endgroup$
0
$\begingroup$

Take a look at page 148 from Aerodynamics for Naval Aviators, a great book freely available. https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/media/00-80T-80.pdf

This picture from the book shows how prop efficiency is related to blade pitch and advance ratio (which is proportional to speed). The top shows how it varies for a series of fixed pitches.

The bottom part shows how prop efficiency varies for a constant speed prop, which shifts $\beta$ to absorb the power coming out of the prop, resulting in a blade position that is ideal for that particular speed.

enter image description here

The ideal efficiency curve for the constant speed prop can be shifted through the prop design, with the peak efficiency in the plot potentially designed for a takeoff condition, cruise, etc.

Also note in the bottom plot how thrust varies with advance ratio (it shows speed on the horizontal axis, but it is really advance ratio). For takeoff or landing, where you want maximum thrust available and are willing to sacrifice efficiency for a period of time, you'd like to run the prop at a low advance ratio. It naturally happens that as you slow down the advance ratio lowers, but you can further decrease it by increasing the RPM if you have an engine where the engine and prop RPM are not directly coupled (e.g., turboprop with an N1 and N2 turbine). If you've flown on a Dash-8, you'll note how they use a higher RPM for takeoff and landing, and a lower RPM once up and away. More thrust available in the landing pattern, more efficiency in cruise.

Improve this answer
$\endgroup$
0
$\begingroup$

Another good reference is this McCauley booklet in which

Professor Von Kliptip Answers Your Questions About

The McCAULEY CONSTANT SPEED PROPELLER GOVERNING SYSTEM

FOR NON-COUNTERWEIGHTED PRESSURE TO INCREASE PITCH PROPELLERS ON TYPICAL SINGLE ENGINE AIRCRAFT

Reading it, one can see the method of spring/flyweights/oil pressure controls the piston that determines the amount of blade twist.

Onspeed, Underspeed conditions and overspeed conditions described on pages 10, 11 discuss how constant speed (RPM) is maintained in climb and descent conditions.

Sorry, I don't see a way to attach it, you'll have to deal with the link. Page 6 on the left and 7 on the right let you see the whole diagram presented.

https://www.airtreknorth.com/uploads/4/7/2/4/4724302/von_klip_tip_cs_propeller.pdf

(prints best on 8.5 x 11 when scaled to fit to page).

Improve this answer
$\endgroup$
0

You must log in to answer this question.

Not the answer you're looking for? Browse other questions tagged .