# How is varying modulation depth achieved by localizer ground transmitters?

An approaching aircraft's navigation receiver uses the difference in depth of modulation between the 90Hz and 150Hz signals which are amplitude modulated onto an RF carrier (on a channel between 108Mhz and 118MHz).

My understanding is that the ground transmitter is formed by several pairs of transmitters forming two interleaved phased arrays to achieved directional beam forming.

My questions is how is the difference in modulation depth achieved by the transmitter system based upon aircraft's position relative to the landing strip's entreline? The beam strength decreases as you move away from it's own centreline, so is it actually that the entire modulated signal strength decreases which when de-modulated is effectively a difference in amplitude modulation depth?

• Possible duplicate of How does ILS (Instrument landing system) work? Commented Jan 25, 2018 at 13:52
• The 90 Hz and 150 Hz beams are separate beams and the Localizer path is the 'valley' in the middle. Commented Jan 25, 2018 at 13:55
• The other question has an answer which says "The position of the needle is determined by which lobe of the transmitter is being received stronger than the other", so it doesn't answer the depth of modulation part (amplitude is not modulation depth).
– mins
Commented Jan 25, 2018 at 18:38

## 2 Answers

The beam strength decreases as you move away from it's own centreline, so is it actually that the entire modulated signal strength decreases which when de-modulated is effectively a difference in amplitude modulation depth?

Your question is a really good one. The depth of modulation is the ratio between the modulation amplitude and the carrier amplitude. Changing the relative strength of a signal changes both amplitudes in the ratio, but keeps the ratio unchanged. No DDM can indeed appear this way.

The 90 and 150 Hz tones are not used directly. The heart of the system creating the DDM is two signals: CSB (carrier and sidebands, see below what is a sideband) and SBO (sidebands only) and surprise! they are containing the same quantity of 90 and 150 Hz tones and are transmitted in equal quantity on both sides of the runway.

Now the key points of ILS:

• SBO phase depends on the runway side (+/-90°, CSB is kept unchanged)
• Phase of the 150 Hz tone is inverted in SBO (90 Hz is kept unchanged).

As SBO contains only the sidebands when CSB and SBO interfere in space, only the sidebands can actually interfere, the carrier found in CSB is unaltered.

When the sidebands interfere, the way they are constructed (by tweaking phases) makes 150 Hz more prominent on the left of the runway, and less prominent on the right side (details below, drawings will clarify). So:

• The carrier amplitude hasn't changed in the process
• The sidebands amplitude has been altered.

As the sidebands are the modulation, in effect there is a change in the DM (the ratio between modulation and carrier amplitude), and a DDM appears magically, increasing as we move away from CSB, that is as we move away from the centerline.

Countless oversimplified descriptions put the focus on 90 and 150 Hz, each one allegedly transmitted on a specific side of the runway (cf. image above). They miss the point the ILS is not based on amplitude comparison, but on depth of modulation comparison.

Two last points:

• A precise location cannot be determined by simply using received signal strength (RSS) of two or more signals. RSS-based positioning improved by averaging algorithms is commonly found for rough positioning (e.g. in cellular networks) because the cost is marginal, but RSS depends on many factors which cannot be controlled.

• On the other hand, the phase of a signal remains unaltered until the signal is reflected, diffracted or enters a material with a different refractive index. By taking appropriate protection measures in the Fresnel zone, the phase-based ILS is therefore very reliable. Phase is used in many sophisticated radio applications. Missing the phase role in the ILS (and conventional VOR) is actually missing the cleverness of these technologies.

If this summary increased your curiosity for more details, just follow on, but for a good understanding, we'll need to first clarify a few notions: Phase, modulation and sidebands.

Phase and phase comparison

When representing a signal, e.g. a sine signal, we can look at different parameters. Often we draw the amplitude as a function of the time (right side):

Two representations of a signal: Phase/amplitude and time/amplitude

We can also imagine a circle with a scale from 0° to 360°, a point traveling on this scale in the time of a signal cycle (left side above).

The phase is the value of the angle. We are usually interested in the phase difference of two signals with the same frequency:

Phase difference

The two signals can be in phase (no difference), in phase opposition (180°), in quadrature (90°) or have any phase difference. The phase difference plays a major role when two signals interfere:

• If the signal are in phase, the amplitude of the result is the sum of the individual amplitudes.
• If the signals are in phase opposition, the amplitudes subtract.
• For any another phase difference, the amplitude of the result is between zero and the sum of individual amplitudes.

In the ILS, basically one signal is sent for reference (CSB) and one signal is sent for comparison (SBO). SBO on one side creates additive interferences with CSB, and substractive interferences on the other side. But actually because 150 Hz is inverted in SBO, on the additive side, at the center of the interference area, 150 Hz cancels itself, 90 Hz doubles its amplitude. On the other side 150 Hz doubles its amplitude, 90 Hz is cancelled. As we move away from the center of the interference area, this additive/subtractive effect decreases until SBO is left unaltered because we are out of CSB area.

Now let's clarify the part related to the modulation and depth of modulation.

Amplitude modulation, depth of modulation, sidebands

Modulation relates to a carrier, which is just a fancy name for a constant (usually sine) RF signal at a given frequency, therefore with all the wave energy concentrated at this frequency. The frequency of the carrier is usually very large compared to the modulation.

The modulating signal (or modulation) is the signal to transmit, it can have any shape, but in our case its shape is a 90 Hz or 150 Hz sine curve.

The amplitude modulation consists in changing the carrier instantaneous amplitude according to the modulation instantaneous amplitude. After it's done, the carrier outer envelope reflects the modulation outer envelope:

Carrier modulated at 50%

The modulation can imprint itself at a variable depth (taller or smaller peaks). This is measured by the modulation index aka depth of modulation. The index value is an amplitude ratio: modulation amplitude / carrier amplitude.

The depth of modulation used for the LOC signal is only 20% (40% for the G/S signal) to leave some room for identification tones on 1020 Hz.

ICAO definition for ILS modulation depth:

The depth of modulation is the ratio of the amplitude of the modulation of the 90 Hz or 150 Hz signal to the carrier amplitude. The DDM is the modulation depth of the stronger signal minus the modulation depth of the weaker signal.

Let's look at how energy is distributed according to frequency.

Spectrum of a carrier AM modulated by a sine tone

Before modulation, all energy is concentrated at the carrier frequency (blue bar below). The modulation process creates two variable sidebands: lower (LSB) and upper (USB), depicted in magenta.

If the modulation index is 100%, the carrier contains 66% of the energy and each sideband 17% (mathematical explanation). When a 100 MHz carrier is modulated by a 150 Hz tone, the LSB is created at 100 MHz - 150 Hz, and the USB at 100 MHz + 150 Hz.

The larger the depth of modulation, the larger the energy transferred from the carrier to the sidebands and the lower the energy remaining at the carrier frequency. Sideband energy and depth of modulation are the two sides of the same coin. In the next paragraphs I'll talk about energy rather than depth, but it's the same.

Modulating the ILS signal with 90/150 Hz tones

The localizer signal is modulated by two tones, the reference at 90 Hz, the signal to compare at 150 Hz. Therefore each sideband energy is split between two frequencies:

CSB signal spectrum

This signal, known as CSB (carrier and sidebands) will be used as-is in the localizer. However as explained earlier, the in-phase / out-of-phase element must be sent along with CSB.

From 90/150 Hz modulations to CSB/SBO modulations

The localizer transmitter sends an additional signal with an inverted 150 Hz, known as SBO (sidebands only). For this signal the carrier element is cancelled (DSB-SC modulation):

SBO signal spectrum with 150 Hz modulation inverted

The signal is sent in phase opposition with CSB on the left side of the runway, and in phase with CSB on the right side (this is done using phase shifters at the antenna level, see further down).

To summarize:

• The localizer transmits CSB on the left and right sides of the array. CSB contains both 150 Hz and 90 Hz with no phase adjustment, and the carrier.

• The localizer also transmits SBO which contains only the sidebands, but where the 150 Hz modulation is phase-shifted by 180° on both sides. The SBO signal itself is sent with a different phase on each half of the antenna array.

How CSB and SBO are sent by the antennas

The actual phase between SBO and CSB is adjusted to compensate for space modulation effects, and SBO is sent with a +90° phase relative to CSB for the antennas on the left of the runway centerline, and with a -90° phase relative to CSB for the antennas of the right of the enterline (the two sides of the array still have a 180° phase difference).

The combination of exact opposite phases for SBO signal cancels the EM field at the center, splitting the SBO radiation pattern in two portions, it seems there are two beams for SBO. CSB is radiated centered on this hole:

CSB + SBO radiation pattern

The elements compositing CSB and SBO must be synchrone. Phases are adjusted carefully to form the radiation pattern (i.e. align the loalizer with the centerline and set its width) and to ensure the linearity of the DDM in the central portion.

When spread in space, the three signals mix by space modulation, the principle the ILS is based on and which is more simply known as wave interference.

Space modulation

One signal (SBO) has its carrier suppressed preventing the carrier energy to be increased during the mix CSB+SBO. In contrary when mixing the sidebands from each signal, the space modulation adds the sidebands energy where the sidebands are in phase, and subtract the sidebands energy when they are in phase opposition.

SBO is in phase opposition with CSB on the left side of the runway and is in phase with CSB on the right side of the runway.

• Along the centerline CSB only is present, with equal energy for 90 Hz (green) and 150 Hz (magenta). The LOC indicator will be centered. In order to create a CSB prominent area along the centerline, SBO power is also reduced on the center antennas.

• On the left side, 150 Hz modulation has been shifted by 180° in SBO, and SBO signal has been shifted 180° relative to CSB at antenna level. 150 Hz modulation is therefore in phase for CSB and SBO. Sideband energies are added, while energy for 90 Hz modulation is decreased because 90 Hz modulation in CSB and SBO are out of phase. So there is more energy for 150 Hz (which means there is a larger depth of modulation). This effect is getting stronger as we move away from the centerline.

• On the right side where 150 Hz modulation is out of phase for CSB and SBO, 150 Hz energy is reduced compared to 90 Hz energy in the sidebands, and the difference is getting stronger as we move away from the centerline.

Past 10° from the centerline, CSB cannot be sensed, only SBO can, the LOC indicator will deviate to full scale left or full scale right depending on the phase of SBO. Another signal is used to ensure a full scale deviation past this point (see clearance signal further down).

If you want to do some space modulation simulation, here are the details of the signals to mix (see details here):

$$E_{CSB} = E_C \space \cos \space 2 \pi f_C t + E_{90} \space \sin \space 2 \pi f_{90} t \space \cos \space 2 \pi f_C t + E_{150} \space \sin \space 2 \pi f_{150} t \space \cos \space 2 \pi F_C t$$
$$E_{SBO \space 90} = K \space \sin \space 2 \pi f_{90} t \space \cos \space 2 \pi f_C t$$
$$E_{SBO \space 150} = K \space \sin \space 2 \pi f_{150} t \space \cos \space 2 \pi f_C t$$

We talked about the sidebands energy. Regarding the carrier, which is only present in CSB, the space modulation result always contains the energy of the original CSB carrier until reaching full scale (then the clearance signal provides the carrier because while all modulation information is in the sidebands, the constant carrier is necessary to synchronize and lock the receiver and to retrieve the coherent CSB and SBO from the modulated radiofrequency resulting signal).

Where the DDM finally appears

Now let wrap up:

• The carrier energy is not changed by the space modulation as it is present in only one signal (CSB).
• The sidebands energy is increased or decreased in the resulting signal.

The energy of the sidebands varies relatively to the energy of the carrier, but wait... this is the same than saying the DM is varying (without actually changing anything at the transmitter level).

The DDM between 150 and 90 Hz, is a function of the receiver offset from the centerline (in the range -5° to +5° the function is quasi-linear).

The space modulation actually creates a DDM

The alignment offset is determined by sensing the DDM in the resulting signal.

Antenna array

The LOC antenna is an array system, usually made of a large number of individual log periodic antennas, to form a narrow directional beam.

Localizer array at Melbourne airport, source

CSB and SBO are not distributed equally to all individual antennas of the array. Before reaching the antennas, their amplitude is tuned to form the three sub-beams, and the SBO signal is phase-shifted:

Individual amplifier-phase shifter-mixer

We have now all the basic elements to draw a LOC system:

Components of the ILS LOC system

Example with an array of two antennas (and final answer to the question)

Let's imagine two antennas fed with our earlier CSB and SBO signals with SBO phase being shifted by +90° for antenna 1 and by 270° for antenna 2.

Two antennas with phase shift of 90° and -90° (270°)

Let's see what happens when the receiver is on the centerline at P0, and at any point P1. For this simplified explanation to work, distance to LOC array (D) must be much larger than distance between antennas and centerline (d).

Receiver on the centerline

The received signal is the sum of the signals sent by the two antennas. As the distance traveled is the same, the phase at the receiver location is also the same. The signal at point P0 on the centerline is:

$$S_{P0} = K_1 \cdot (CSB - SBO) + K_2 \cdot (CSB + SBO)$$

With $$K_1$$ and $$K_2$$ being the attenuation in free space, as the attenuation is the same for both antennas, this can be simplified:

$$S_{P0} = K_1 \cdot [(CSB - SBO) + (CSB + SBO)] = 2K_1 \cdot CSB$$

In CSB, the 90 Hz depth of modulation is the same than the 150 Hz one (see previous figure) There is no difference in depth of modulation (DDM) between the tones: DDM = 0%.

Receiver at point P1

The distance traveled is shorter for antenna 1, and longer for antenna 2. A phase lead and a phase lag respectively appear for antenna 1 and antenna 2. The phase lead is also equal to the phase lag. After some simplification that can be read in the linked thesis:

$$S_{P1} (\beta) = 2K_1 \cdot (\cos \beta \cdot CSB - \sin \beta \cdot SBO)$$

with $$\beta$$ being the angular distance from the centerline. This formula shows:

• when $$\beta$$ is null (receiver on the centerline), we have the result already seen in the previous case,

• when $$\beta$$ is negative or positive, the SBO signal influence increases and the overall depth of modulation between 150 and 90 Hz tones follows the same trend until reaching -100% or +100%, which correspond to the absence of CSB signal influence at the receiver side.

Actual principle of the ILS, from this source.

The range of difference of depth modulation obtained must be mapped on the actual standardized values for LOC needle deviation, reducing the full range to a standardized guidance angle. The LOC specification are found in ICAO annex 10 to the Chicago Convention, volume 1, attachment C:

This setting is obtained by tuning the amplifier of the phase-shifter from each individual antenna (the amplifier is actually common to all antennas). This amplifier reduces the SBO signal influence on the DDM.

Clearance signal

So far we have assumed the localizer signal is only composed of the course guidance mixing the two original signals CSB and SBO. But it is very difficult to obtain an actual highly directional beam, like the course beam, without creating unwanted lobes:

Radiation pattern of beam antenna, source

The problem with the secondary lobes is an aircraft approaching aligned with one of them will see it as being the main lobe, and will approach the runway using a wrong course. There are some techniques to minimize these unwanted lobes, but none is practical for large arrays like a LOC system. Alternatives are to block the unwanted waves after they are radiated, or to flood them, the solution used for ILS.

A replica of the course, the clearance signal, is sent with the course signal to outshine the secondary lobes.

The clearance signal has a power level of 10 dB less than the course level (a tenth of the power) and is radiated with a less directional pattern (less individual antennas to form the beam):

Course and clearance

Today's localizers use a dual frequency system, this means the course and clearance signals are sent on separate frequencies.

When an ILS has a published VHF frequency f, the localizer course signal is actually sent on f + 4.75 kHz and the clearance on f - 4.75 kHz. The two signals can use the same aerials or dedicated antennas in the array. Example of signals send to each of the 14 antennas of a Thales LLZ array (refer to above for what are course, clearance, CSB and SBO signals):

Most of the information about ILS come from the 1983 thesis presented by Capt Dennis M. McCollum, B.S.. Respectful thanks to the author.

• From the image it looks like the clearance signal cancels the side lobes but not the back lobe, which would make sense (because back-course approaches, etc.). Also: Amazing answer. Commented Jan 27, 2018 at 11:10
• @WayneConrad: Right. If the back lobe needed to be hidden, I believe other ways than flooding by clearance are available, e.g. reflectors on the antennas. Flooding would need more power in the clearance signal, as the back lobe is usually very energized, including for the log periodic antennas used.
– mins
Commented Jan 27, 2018 at 11:26
• That was clear enough that I sorta, kinda, more-or-less understood it! Is this the kind of detail that pilots are expected to know, or is this an area of interest/specialty of yours, @mins? Commented Oct 18, 2019 at 18:32
• @FreeMan: Thanks a lot. This is more a topic of electronics engineering than pilot training. However, for a pilot it matters to know that if SBO is down, but CSB is live, the CDI will indicate "aligned" at any location, there was a serious incident based on this condition in July 2000.
– mins
Commented Oct 18, 2019 at 21:06

Ok probably the best explanation of ILS going around! well done! I teach ILS to maintenance engineers and technicians,you could do my job-im sure! Thanks for using my Space Modulation article from Wikipedia too!. although it's not completely wave interference/superposition, it's a lot more complex, but close enough.

There's DDM and SDM values once again were explained well-the Wikipedia articles for those are mine as well, LOL.

The DDM is determined by the combined resultant phasor (electronics version of vectors-used to represent signals rather than forces), addition/subtraction of the carrier wave power of the CSB and the two different frequency 90 and 150 hz modulation depths both 20% at the antenna and the SBO (sideband Only) power and 90 and 150 Hz modulation depths, again a phasor addition/subtraction !

When all those phases and powers combine in (air)space where the plane receives them, the ILS display effectively measures, a difference current in the indicator needle of between -150 microamps and +150 microamps.

if the plane is on centreline approach, the DDM is 20% 90Hz and 20% 150Hz = 0 % Difference between them, the needle remains centred-the plane is on centreline.

The Clearance is at a different frequency, but within the bandwidth of the avionics channel for the Course, (difficult concept) so it does not cancel the sidelobes-it swamps them! The Course sidelobes that are not within the navigable course path per-se.

The ILS concept is simple but the technology (from 1938!) is incredibly well engineered! I've been teaching it for 15 years and EVERYtime I run a class, I learn something else about this system, I've worked on RADARs, MRI machines, CT scanners and Nuclear Medicine equipment-its up there in the technology stakes!

• Welcome to Aviation.SE! Your answer starts like a comment referring to another answer. We prefer it here if answers are all standalone answers to the original question. Could you re-phrase this post accordingly? Once you have enough reputation, you can comment under the other answer... Commented Aug 19, 2020 at 6:44
• Welcome Richard! Yes ILS and DVOR were really superbly designed, making the best use of reliable phase difference, at a time radio applications were mostly based on unreliable wave amplitude. Thanks for all your contributions on Wikipedia (I see I read many of the articles you contributed to), I hope you'll write here too.
– mins
Commented Aug 19, 2020 at 11:09