The landing gear should be down in order to qualify as a stabilized approach. Other than that, what are the guidelines on when to deploy landing gear on approach?

  • 21
    $\begingroup$ "Before contact with the ground" is generally considered to be optimal, and has noise abatement benefits (what's louder: the gear horn, or the sound of metal dragging on the runway?) $\endgroup$
    – voretaq7
    Commented May 3, 2014 at 1:32
  • $\begingroup$ Just opened this site to ask pretty much the same question and yours was the first of the top questions :D $\endgroup$ Commented May 19, 2014 at 6:43
  • 6
    $\begingroup$ @voretaq7 In addition to the noise abatement concerns, I hear it also has significant operational cost and even customer satisfaction benefits. $\endgroup$
    – reirab
    Commented Feb 1, 2015 at 4:23
  • $\begingroup$ I have never flown P1 in a retractable gear a/c, but the downwind checklist had it gear as the second item (brakes, undercarriage, mixture, pitch, carb. heat, fuel, flaps, gauges, hatch, harness) :-). $\endgroup$
    – copper.hat
    Commented Apr 20, 2019 at 20:07

3 Answers 3


As late as possible to still meet your company's specific stabilized approach guidelines (mine were 500 ft VMC, 1000 ft IMC). If you need the drag, then use them earlier.

In the EMB-145 in still wind or a headwind you could cross the FAF at 250 kts and clean and be on speed and configured by 1000' if you dropped the gear at the FAF (and opened the speed brakes and the first notch of flaps all at once). Normally though, I'd drop the gear around 1000'.


  • VMC = visual meteorological conditions
  • IMC = instrument meteorological conditions
  • FAF = final approach fix
  • EMB-145 is the type designator for the Embraer 145 regional jet
  • 3
    $\begingroup$ Could you define the acronyms? $\endgroup$
    – CGCampbell
    Commented May 19, 2014 at 0:43
  • 1
    $\begingroup$ @CGCampbell VMC = visual meteorological conditions, IMC = instrument meteorological conditions, FAF = final approach fix, EMB-145 is the type designator for the Embraer 145 regional jet. $\endgroup$
    – casey
    Commented May 19, 2014 at 1:10
  • $\begingroup$ In my airplane, dropping the gear at Vle at the FAF will give a nice fast stabilized approach $\endgroup$
    – rbp
    Commented Feb 1, 2015 at 12:58

In light general aviation aircraft, you lower the gear when abeam the touchdown point on downwind, then double-check that the gear is down on final (and possibly on base, as well).

  • 2
    $\begingroup$ On light general aircraft, the gear is down and welded. The number of retracts in service is less than 5% of the fleet, and gear deployment techniques vary $\endgroup$
    – rbp
    Commented Feb 1, 2015 at 12:55
  • $\begingroup$ That’s what I do as well. Gear, first notch of flaps, and reduce power together so you don’t climb or descend a bit when deploying them. Then slow the airplane and begin a 500' per minute descent to landing. $\endgroup$
    – JScarry
    Commented Aug 3, 2019 at 13:23

It should normally be dropped about 500ft - 1000ft and below the aircraft's maximum speed for dropping the landing gear so you don't damage it. If you need more drag to slow down quicker you can drop it a bit higher up.


You must log in to answer this question.

Not the answer you're looking for? Browse other questions tagged .